COMPONENTS

• 8MM
• Rush's NanoCeramic Lube self-repairs under extreme friction
• Reinforced premium-grade nylon ball retainer
• Heat treated
• Titanium coating 
• Lightweight, fast, strong and fluid. Spacers included
• Set of 8 bearings

• Precision engineered by Shiver
• Best in class lubricant
• Built-in speed rings
• Built in spacers

• 8MM
• Lightweight, fast, strong and fluid
• Set of 8 bearings

Package includes ONE protective rubber strip for regular 3/4" decks (does not fit 1" upgrade decks)

Features：

1. Prevents nicks and chips or to cover existing damage to the nose or tail of your board

2. U channel design allows an easy fit over the deck edge 

3. High quality rubber material that is heat resistance, abrasion resistance, anti-aging, waterproof

4. Install easily with no tools: Center the strip in the desired location.  Push down on the middle of the strip until fully seated, then work down each side. 

Will not damage the board during installation. Fully removable and re-attachable.

Keep your board looking fresh and new. 

#1 Cleaner to wipe down and clean your board

#2 Compound to buff out light surface scratches 

#3 Compound to buff out heavy surface scratches

How to use:

1. For general cleaning apply #1 liberally to a microfiber towel and wipe down the board

2. For light scratches apply dime sized amount directly to a buffing pad (either hand or powered), work back and forth across the board evenly. Wipe and clean with #1.

3. For heavy scratches apply dime sized amount directly to a buffing pad (either hand or powered), work back and forth across the board evenly.  Wipe clean. Apply dime sized amount of #2 directly to a buffing pad (either hand or powered), work back and forth across the board evenly. Wipe and clean with #1.

The Revel Kit is a direct drive bolt-on electric skateboard, designed from the ground up for unparalleled versatility, massive performance, and using premium parts and materials.

It works with a variety of standard longboard wheels, and it can be installed on most decks with just 4 screws like a standard skateboard truck.

The kit is available with two battery options:

Standard range battery (144wh/4000mAh)
Extended range battery (216wh/6000mAh)

Revel remote can be paired to two kits simultaneously, for a 4WD riding experience.

• Direct drive bolt-on electric skateboard 
• Fast install on most decks
• Everything included (except a deck!)
• Swappable batteries
  
• 4WD ready remote control 

KIT SPECS

• Top Speed 28 Mph / 45 Kmh
• Standard Range Battery 6-10 Miles / 10-16 Km
• 144WH / 4000mAh
• Extended Range Battery 10-15 Miles / 16-24 Km
• 216WH / 6000mAh
• Max Grade: 20%
• Charge Time 120-180 Minutes
• Drive Weight 11 Lbs / 5 Kg
• Standard Wheels 90mm
• Truck Width 11" / 280 mm
• Throttle Control Linear
• Max Rider Capacity Tested to 264 Lbs / 120 Kg
• Motors 1100W Dual Brushless Motors
• IP Rating Water & Dust Resistant (IP 54)
• Braking Regenerative Braking
• Remote Connection Bluetooth Low-Energy
• Operating Temp 32 to 104 °F / 0 to 40 °C

Double the range of your Revel Kit with an extra 144WH battery pack! The standard range battery can go up to 6-10 Miles / 10-16 Km.

• ABEC 7 Rated Bearings
• Rubber Seals to repel water
• 608RS with Oiled Lubrication

Wheels set (4)

Wheels set (4)

Wheels set (4)

Wheels set (4)

Wheels set (4)

Wheels set (4)

Wheels set (4)

Wheels set (4)

Wheels set (4)

Wheels set (4)

Set of (4) wheels

70mm LED

Set of (4) wheels

70mm LED

Set of (4) wheels

70mm LED

Set of (4) wheels

70mm LED

Set of (4) wheels

70mm LED

Set of (4) wheels

70mm LED

Set of (4) wheels

70mm LED

Set of (4) wheels

70mm LED

Super REDS® are designed from the ground up to be the best bearing on the market at this price point. What Super REDS® are not is a REDS® bearing with just better super finishing (surface polishing). Super REDS® are a superior quality bearing, using higher quality steel races, better quality and grade balls, and a superior surface finish. The result is a bearing that is as fast as REDS® but quieter, smoother, and longer lasting. Super REDS® use a black shield and laser engraving to differentiate themselves from original REDS®.

Features

• Features Higher quality steel races, better quality and grade balls, and a superior surface finish.
• Single, non-contact, removable rubber shield for easy cleaning and less friction.
• High speed nylon ball retainer for greater strength and speed.
• Pre-lubricated with Speed Cream™ racing lubricant
• Skate Rated™ clearances, tolerances, materials and lubricant provide the best performance and durability possible.

Contents

• Set of 8 bearings
• Instructions
• Sticker

Each Bones Race REDS Bearings is made with upgraded top quality bearing steel, ground to perfection and polished, best for racers who use precision trucks and properly tighten their axle nuts

Precision ground 0.200 built in spacer to provide perfect 0.400 spacing between bearings.

Precision ground extended race eliminates the need for speed washers, and provides better alignment of the bearings when the axle nut is tightened.

Lubricated with Bones Speed Cream

A groove on the inside of each bearings inner race eliminates weight and allows insertion and removal of the bearing using the Bones Bearing Tool, even on hub wheels

Features

• Precision ground, Skate Rated™ Racing bearings by Bones®
• Removable high-speed Nylon™ ball retainers
• Removable Non-Contact frictionless shield for easy cleaning
• Integrated bearing spacer to provide perfect 0.400" spacing
• Extended race replaces need for spacers and washers
• Extended race provides perfect alignment for greater speed and axle reinforcement

Bones® REDS® are manufactured in China to our Bones Skate Rated™ specifications in a manufacturing facility dedicated to producing the highest quality skate bearings in China. They are inspected twice before being shipped to skaters and offer the greatest combination of performance, durability and low cost in the industry. Because they offer near Bones Swiss performance at a fraction of the cost, they have become the best selling bearings.

Features

• Single, non-contact, removable rubber shield for easy cleaning and less friction
• High speed Nylon™ ball retainer for greater strength and speed
• Pre-lubricated with Speed Cream™ racing lubricant
• Skate Rated™ clearances, tolerances, materials and lubricant provide the best performance and durability possible
• Contents

Instructions
Sticker

• Features grade 5, silicone nitride, hot isostatically pressed ceramic balls.
• Higher quality steel races and a superior surface finish.
• Single non-contact removable rubber shield for easy cleaning and less friction.
• High speed nylon ball retainer for greater strength and speed.
• Pre-lubricated with Speed Cream racing lubricant.
• Skate Rated clearances, tolerances, materials and lubricant provide the best performance and durability possible.

• Set of 8 bearings
• Instructions
• Sticker

Package includes ONE protective rubber strip for upgraded 1" decks (does not fit regular 3/4" decks). Only select if you upgraded to a 1" deck.

Features：

1. Prevents nicks and chips or to cover existing damage to the nose or tail of your board

2. U channel design allows an easy fit over the deck edge 

3. High quality rubber material that is heat resistance, abrasion resistance, anti-aging, waterproof

4. Install easily with no tools: Center the strip in the desired location.  Push down on the middle of the strip until fully seated, then work down each side. 

Will not damage the board during installation. Fully removable and re-attachable.